Aussie Joey 7110 Series Uživatelský manuál

Aussie®bbyy MMeeccoo®LP Gas GrillAssembly and Use ManualJoeyTMFor Customer Service, call 1-800-251-7558 or visit our web site at www.meco.netFOR OUTD

10(27) BOLT, M6X15 8 PC(28) SCREW, M6X15 FIG. 6AFIG. 6B(27) BOLT, M6X15 (26) LEFT SIDETABLE(25) RIGHT SIDETABLEStep 6) Assemble Side Tables:Align bra

Step 10) Install Cooking Grid:(Note Warming Rack already installed.)Lay Cooking Grid onto the Bowl ridges over theFlame Diffuser and Main Burner. (FIG

12To reduce the risk of serious bodily injury or death:· Use only propane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural

CylinderRetainer ClipCylinderCarry HandleTo avoid pinching in next step, keep fingersand hands near corners of Cylinder RetainerClip when swinging Cli

14To reduce the risk of serious bodily injury or death:· This outdoor cooking appliance shall be used only outdoors and shall not be used in a buildi

151. Open the Hood.2. Important: Make sure all control knobs are turned “Off”. (FIG. 13A)3. Turn the LP Gas Cylinder valve open counterclockwise until

16MANUAL LIGHTING THE GRILL1. Open the Hood.2. Important: Make sure control knobs are turned “Off”. (See FIG. 13A)3. Turn the LP Gas Cylinder valve op

17Closing the Hood forms an ‘oven’ and traps a large amount ofheat for roasting whole meats, chickens, etc. Therefore, it isIMPORTANT that the burner

181) Remove Drip Cup, Cooking Grid, and Flame Diffuser.2) Drip Cup-Wash the Drip Cup with soap and water. 3) Grill Body and Cart-Remove excess grease

195) Use a pipe cleaner to clear insect nests from the inlet hole of main burner (FIG. 15D). Open up the main burner holes with a small nail or wire.N

2I. Assembly Instructions...2Parts Illustrations...

Problem:Possible Cause:Solution:Burner will not light using the ignitorBurner is not connected toValve.Not pausing long enoughbefore clicking the Igni

21TROUBLESHOOTING (Cont’d)Persistent greasefireUnable to fillLP tankHumming orwhistling fromthe regulatorGrease trapped aroundburner systemSome deal

IMPORTANT NOTICEThis Gas Grill must be used with a LP Gas Cylinder equippedwith an OPD (Overfill Prevention Device).This is a secondary device to pre

MECO CORPORATIONLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material andworkmanship under normal o

P/N 03.6602.00REL. 11/06 Aussie®

3PARTS ILLUSTRATIONSIf you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you havean

(38) Flame Diffuser(39) Cooking Grid(37) Fabric Panel(43) LP CylinderHeat Shield(41) Main Burner(42) Main BurnerElectrode(44) Control Panelw/Manifold

519 Sidebrace, Right 03.6615.00 120 Sidebrace, Left 03.6616.00 121 Screw, ST 4.0 x 10 03.6583.00 1222 Bolt, M4 x 10 (Clear Nickel) 03.6267.00 223 Win

6STEP 1) Cart Assembly:Attach the Legs to the Bottom Shelf withM5 x 40 Bolts threaded into the BottomShelf holes. Position legs with the holesexactly

STEP2) Assemble Axle, Wheels & Wheel Covers:7(10) WHEEL2 PC(12) WHEEL COVER2 PCPush Axle through center hole in Wheel and through lower hole in

Step 4) Install Drip Cup:Insert Drip Cup into Drip Cup Holder ring untilthe cup flange is flush with the ring and thenotch in the lip of the cup fits

9Step 5) Assemble Sidebraces:· Attach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG. 5A) Secure Bottom Heat Shield to L